Stainless Steel Bathroom Faucet Manufacturer Shares The Steps Of Leak Treatment (Automobiles & Vehicles - SUVs & Trucks)

UKFreeAds > Automobiles & Vehicles > SUVs & Trucks

Item ID 1071509 in Category: Automobiles & Vehicles - SUVs & Trucks

Stainless Steel Bathroom Faucet Manufacturer Shares The Steps Of Leak Treatment




US Free Ads
The Most Popular Online Classifieds in USA.
No Sign up, No Email Required to Post.



US Free Advertising
Free Advertising Classified Ads.
Free Internet Web Site Advertising.

Many people will have dripping water and leaking water in their homes. Most people don't care much at first. It is not a big deal to feel that one or two drops of water are missing. But in fact, this undoubtedly caused a lot of water waste. Below, the Stainless Steel Bathroom Faucet manufacturer introduces several solutions for leaking faucets.

1. Push-type faucet leaks
Step 1: Close the inlet valve. Remove the small screws on or behind the faucet handle to remove the handle that is attached to the faucet body. Some screws are hidden under metal buttons, plastic buttons or plastic sheets that are snapped or screwed into the handle. Simply open the button and you will see the handle screw on the top.

Step 2: Remove the handle and look at the parts of the faucet. Use a large pliers or an adjustable wrench to remove the packing nut, taking care not to leave scratches on the metal. Rotate the spool or shaft in the same direction as when you turned the faucet to unscrew them.

Step 3: Remove the screws that secure the washer. If necessary, use an infiltration lubricant to loosen the screws. Check the screws and spools and replace them if they are damaged.

Step 4: Replace the old gasket with a new one that is identical. New gaskets that are almost perfectly matched to the old gaskets generally allow the faucet to no longer drip. Also note that the old washer is either beveled or flat and replaced with the same new washer. A gasket designed only for cold water will swell significantly when hot water flows to block the water outlet, making the hot water flow slower. Some washers work in both hot and cold water, but make sure that the gasket you bought for replacement is exactly the same.

Step 5: Secure the new gasket to the valve plug and reassemble the parts in the faucet. Rotate the spool clockwise. After the spool is in place, reinstall the packing nut. Be careful not to leave the wrench scratched on the metal.

Step 6: Reinstall the handle and replace the button or disc. Re-open the water supply and check for leaks.

2. The faucet leaks due to the sealing ring of the faucet
Step 1: Turn off the water supply and remove the faucet handle.

Step 2: Unscrew the packing nut and remove the nut and the old seal from the valve plug.

Step 3: Install a new seal. If you are using a linear sealing material, wrap it around the spool a few turns. If it is a sealing material such as a soft wire, it is only wrapped around the valve core.

3. The O-ring of the faucet will also cause the faucet to leak
Step 1: Turn off the water supply, turn it counterclockwise and remove the threaded coupling nut that secures the water outlet. Be sure to wrap the nut with tape to prevent it from being scratched by pliers or a wrench.

Step 2: After removing the coupling nut, lift the water outlet up and take it out of the water outlet seat. You can see these rings in the water outlet seat.

Step 3: Replace the problematic ring with a new ring of the same size. Reassemble the faucet.


information about Stainless Steel Bathroom Faucet : https://www.afastainlesskb.com/product/stainless-steel-faucet/bathroom-faucet/


Related Link: Click here to visit item owner's website (0 hit)

Target Nation: Wales
Target City : Yuyao
Last Update : 14 February 2019
Number of Views: 63
Item  Owner  : afastainlesskb
Contact Email:
Contact Phone: (None)

Friendly reminder: Click here to read some tips.
UKFreeAds > Automobiles & Vehicles > SUVs & Trucks
 © 2019 UKFreeAds.ws
2019-08-24 (0.078 sec)